Presented here below yow will discover a bunch of awesome ideas on the subject of A Step-by-Step Guide to Installing a Bathtub.
Installing a bathtub isn't exactly rocket science, but it does require solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bathtub with a new one is also a moderately difficult project. If the old bathtub is conveniently obtainable, the task can relocate immediately; if you need to open a wall surface to get rid of the old bathtub as well as place the new tub, the task is much harder. In either case, the project is within a home handyman's skills, although you will certainly require a helper to move out the old tub and embeded in the brand-new one. See to it you have actually certified yourself for the job and are comfortable trying it. As opposed to working with a contractor to take control of a halfway-completed task, it is far better to think about utilizing one before you begin. Opportunities are you might need a professional plumber to make tube connections.
This write-up will certainly aid you set up a new bathtub in your bathroom if you have actually currently purchased a new bathtub as well as don't need to transform the plan of your previous supply of water pipelines.
Your devices and product list ought to comprise the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be quite bothersome because of the restricted gain access to that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a cloth prepared for the remaining water that will certainly come from the pipelines. When the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old securing compound.
Prior to moving on to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to prevent damages to the string. One end of the port fits on the plastic tail of the faucet and also the other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin ensuring that the washers remain in place between the faucet and also the sink. Secure the tap in position with the supplier provided backnut. When the tap is safely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet adapters. The previous type ought to be linked to the tap ends first, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Using the two wood boards under its feet, place the bathtub in the needed setting. The wood boards are handy in evenly spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The following goal is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the tub up until the level reviews degree.
To mount faucets, fit all-time low of the furthest flexible tap connector to the suitable supply pipe by making a compression join; then do the same for the other tap.
Switch on the water supply and check all joints and new pipework for leakages as well as tighten them if needed. Fill up the tub and also check the overflow outlet and the regular electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling and sealing around the bath tub needs to wait till the tub has been utilized at least once as this will certainly resolve it into its final placement.
Getting ready for the Setup
Firstly, the supporting structure provided with the bathroom ought to be fitted (if required) according to the supplier's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its final setting.
Tiling Around the Bathtub
In the location where the bathroom satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack a stiff seal, creating the water to permeate the wall surface between the bath and also the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes and also cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill the tub with water prior to sealing, to enable the activity experienced when the bathtub is in use. The sealer can break fairly very early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed reading our topic on Tools You Need to Install a New Bathtub . Thanks a lot for taking time to browse our article. Do you know about anybody else who is serious about the subject? Why not promote it. We treasure reading our article about A Step-by-Step Guide to Installing a Bathtub.
Book Appointment Now